Sorensen SGI 160/188

Instrumentos:

Para pruebas de:

Inicio > Seleccion por Marca > Sorensen >

Sorensen SGI 160/188, 30kW 160V 188A Fuente de Poder Programable DC.

Sorensen SGI 160/188

Preguntar precio y disponibilidad

Disponibilidad: Preguntar disponibilidad
Codigo del Producto: SGI-160-188

Descripcion

Detalle del producto

Ver Hoja de Datos en formato PDF

Common

Remote Sense	Load-line loss compensation for models <= 100V is 10% above full scale voltage total (5% per load-line), and models > 100V is 4% above full scale voltage total (2% per load-line).
Parallel Operation	Up to 5 units may be paralleled for additional current within the power supply single-unit specifications, with exception of the DC output current set accuracy. Additional paralleled SG units will add 0.3% inaccuracy per unit. To parallel more than 5 units, contact factory.
Series Operation	Up to 2 units (See Output Float Voltage)

Input

Nominal Voltage 3 phase, 3 wire + ground	208/220 VAC (operating range 187 - 242VAC) 380/400 VAC (operating range 342 - 440VAC) 440/480 VAC (operating range 396 - 528VAC)* *Optional
Frequency	47 – 63Hz
Power Factor	>0.9 typical at 208/220 VAC input >0.78 typical at 380/400 VAC input >0.69 typical at 440/480 VAC input
Protection	½ cycle ride-though on all three phases, 3 cycle ride-through on single phase; missing phase shutdown

Input: AC Voltage and Current

Output Power	Max AC Input Current (A) per Phase, Low Line
Output Power	187-242 VAC	342-440 VAC	396-528 VAC
5kW (3U)	21	14	13
10kW (3U)	41	27	26
15kW (3U)	62	40	39
20kW (6U)	83	54	52
25kW (6U)	103	67	65
30kW (6U)	124	80	78

Output: Voltage and Current Ranges

	3U			6U			Ripple & Noise
Power	5 kW	10 kW	15 kW	20 kW	25 kW	30 kW	rms (20Hz-300kHz)	p-p
Voltage	Current						rms (20Hz-300kHz)	p-p
40	125	250	375	500*	625*	750*	20mV	75mV
60	83	167	250	333	417	500	20mV	75mV
80	63	125	188	250	313	375	20mV	100mV
100	50	100	150	200	250	300	20mV	100mV
160	31	63	94	125	156	188	25mV	150mV
200	25	50	75	100	125	150	25mV	175mV
250	20	40	60	80	100	120	30mV	200mV
330	15	30	45	61	76	91	30mV	200mV
400	12	25	38	50	63	75	40mV	300mV
600	8	17	25	33	42	50	60mV	350mV

* By way of paralleling 5kW, 10kW & 15kW supplies

Output

Ripple & Noise (Voltage Mode)	See Output: Voltage & Current Ranges Chart Above. Ripple and noise specified at full load, nominal AC input
Ripple (Current Mode)	<+/- 0.04% of full scale rms current
DC Voltage Slew Rate	100 msec 5-95% of full scale typical (Contact factory for model specific slew rates)
DC Current Slew Rate	45A / ms typical
Line Regulation	(±10% of nominal AC input, constant load) Voltage Mode: +/- 0.01% of full scale Current Mode: +/- 0.05% of full scale
Load Regulation	(no load to full load, nominal AC input) Voltage Mode: +/- 0.02% of full scale Current Mode: +/- 0.1% of full scale
Load Transient Response	Recovers within 1ms to +/-0.75% of steadystate output for a 50% to 100% or 100% to 50% load change
Efficiency	87% typical at nominal line and max load
Stability	±0.05% of set point after 8 hrs. warm-up at fixed line, load and temperature
Temperature Coefficient	0.02%/ C of maximum output voltage rating for voltage set point 0.03%/ C of maximum output current rating for current set point
Output Float Voltage	Negative terminal within +/- 150 V of chassis potential

Physical

Dimensions	Width: 19.00” (48.3 cm), Depth 25.0” (63.5 cm)
	Height: 5-15 kW Units: 3U – 5.25” rack mount (13.34 cm) 20-30 kW units: 6U – 10.5” rack mount (26.67 cm)

Weight & Shipping Weight

Weight	3U, 5kW ~ 40 lbs (18kg) 3U, 10kW ~ 60 lbs (27kg) 3U, 15kW ~ 80 lbs (36kg) 6U, 20kW ~ 120 lbs (54kg) 6U, 25kW ~ 140 lbs (63kg) 6U, 30kW ~ 160 lbs (72kg)
Shipping Weight	3U, 5kW ~ 70 lbs (32kg) 3U, 10kW ~ 90 lbs (41kg) 3U, 15kW ~ 110 lbs (50kg) 6U, 20kW ~ 150 lbs (68kg) 6U, 25kW ~ 170 lbs (77kg) 6U, 30kW ~ 190 lbs (86kg)

	Product Configurator

	DC Electronic Loads

	DC Modular Supply

	Discontinued Products

	Product Support

	Contact Sales

Programming & Read-back Specifications

	Programming		Read-Back / Monitoring
	Accuracy	Resolution	Accuracy	Resolution
Front panel Display	SGA: +/- (0.5%fs + 1 digit) SGI, Voltage: +/- 0.1% of full scale SGI, Current: +/- 0.4% of full scale	SGA: 3.5 digits SGI: 4.0 digits	SGA: +/- (0.5%fs + 1 digit) SGI, Voltage: +/- 0.1% of full scale SGI, Current: +/- 0.4% of full scale	SGA: 3.5 digits SGI: 4.0 digits	Knob control & Display read-back
Remote Analog Interface	Voltage: +/-0.25% of full scale for 0-5V range, +/-0.5% of full scale for 0-10V range Current: 0.8% of full scale	NA	+/-1.0% of full scale (0 - 10V)	NA	25-pin D-sub connector (0~5V or 0~10V)
Remote Digital Interface	Voltage: +/- 0.1% of full scale, Current: +/- 0.4% of full scale	+/-0.002% of full scale	Voltage: +/- 0.15% of full scale, Current: +/- 0.4% of full scale	+/-0.002% of full scale	RS-232C (Standard on SGI), Optional IEEE-488.2 and Optional LXI Compliant 10/100 base-T Ethernet (see Options)
OVP	+/- 1% of full scale	+/-0.002% of full scale			Programming range: 5-110% Configured from front panel, remote analog or via optional digital inputs
User I/O	Disconnect & Polarity-reversal relay control ( Only available with Ethernet Option )				Digital 10-pin Molex type connector Chart Below

Analog User I/O Pinouts

1	Isolated Remote ON/OFF	14	Isolated TTL/CMOS ON/OFF Control
2	Isolated Circuit Return	15	Remote Voltage Programming
3	Remote Overvoltage Set	16	Remote Current Programming
4	Voltage Return for Pins 9, 15, or 21	17	Fault State
5	Remote ON/OFF	18	Shutdown Fault
6	Circuit Common	19	Output Voltage Monitor
7	Output Current Monitor	20	Voltage Return for Pins 9, 15, or 21
8	Local Voltage Control Monitor	21	Voltage Control Resistance
9	Remote Voltage Programming	22	Current Control Resistance
10	Remote Current Programming	23	Current Return for Pins 10, 16, or 22
11	Local Current Control Monitor	24	Circuit Common
12	60V Remote Sense	25	Current Return for Pins 10, 16, or 22

Digital User I/O Pinouts ( Ethernet Option Only )

1	Fold Back Monitor
2	Direct Shutdown
3	Fault Indication
4	Trigger Out
5	Common
6	Polarity output reversal signal
7	Isolation relays relay open signal
8	Sense relays open signal
9	Common
10	Trigger in

Common

Remote Sense	Load-line loss compensation for models <= 100V is 10% above full scale voltage total (5% per load-line), and models > 100V is 4% above full scale voltage total (2% per load-line).
Parallel Operation	Up to 5 units may be paralleled for additional current within the power supply single-unit specifications, with exception of the DC output current set accuracy. Additional paralleled SG units will add 0.3% inaccuracy per unit. To parallel more than 5 units, contact factory.
Series Operation	Up to 2 units (See Output Float Voltage)

Input

Nominal Voltage 3 phase, 3 wire + ground	208/220 VAC (operating range 187 - 242VAC) 380/400 VAC (operating range 342 - 440VAC) 440/480 VAC (operating range 396 - 528VAC)* *Optional
Frequency	47 – 63Hz
Power Factor	>0.9 typical at 208/220 VAC input >0.78 typical at 380/400 VAC input >0.69 typical at 440/480 VAC input
Protection	½ cycle ride-though on all three phases, 3 cycle ride-through on single phase; missing phase shutdown

Input: AC Voltage and Current

Output Power	Max AC Input Current (A) per Phase, Low Line
Output Power	187-242 VAC	342-440 VAC	396-528 VAC
5kW (3U)	21	14	13
10kW (3U)	41	27	26
15kW (3U)	62	40	39
20kW (6U)	83	54	52
25kW (6U)	103	67	65
30kW (6U)	124	80	78

Output: Voltage and Current Ranges

	3U			6U			Ripple & Noise
Power	5 kW	10 kW	15 kW	20 kW	25 kW	30 kW	rms (20Hz-300kHz)	p-p
Voltage	Current						rms (20Hz-300kHz)	p-p
40	125	250	375	500*	625*	750*	20mV	75mV
60	83	167	250	333	417	500	20mV	75mV
80	63	125	188	250	313	375	20mV	100mV
100	50	100	150	200	250	300	20mV	100mV
160	31	63	94	125	156	188	25mV	150mV
200	25	50	75	100	125	150	25mV	175mV
250	20	40	60	80	100	120	30mV	200mV
330	15	30	45	61	76	91	30mV	200mV
400	12	25	38	50	63	75	40mV	300mV
600	8	17	25	33	42	50	60mV	350mV

* By way of paralleling 5kW, 10kW & 15kW supplies

Output

Ripple & Noise (Voltage Mode)	See Output: Voltage & Current Ranges Chart Above. Ripple and noise specified at full load, nominal AC input
Ripple (Current Mode)	<+/- 0.04% of full scale rms current
DC Voltage Slew Rate	100 msec 5-95% of full scale typical (Contact factory for model specific slew rates)
DC Current Slew Rate	45A / ms typical
Line Regulation	(±10% of nominal AC input, constant load) Voltage Mode: +/- 0.01% of full scale Current Mode: +/- 0.05% of full scale
Load Regulation	(no load to full load, nominal AC input) Voltage Mode: +/- 0.02% of full scale Current Mode: +/- 0.1% of full scale
Load Transient Response	Recovers within 1ms to +/-0.75% of steadystate output for a 50% to 100% or 100% to 50% load change
Efficiency	87% typical at nominal line and max load
Stability	±0.05% of set point after 8 hrs. warm-up at fixed line, load and temperature
Temperature Coefficient	0.02%/ C of maximum output voltage rating for voltage set point 0.03%/ C of maximum output current rating for current set point
Output Float Voltage	Negative terminal within +/- 150 V of chassis potential

Physical

Dimensions	Width: 19.00” (48.3 cm), Depth 25.0” (63.5 cm)
	Height: 5-15 kW Units: 3U – 5.25” rack mount (13.34 cm) 20-30 kW units: 6U – 10.5” rack mount (26.67 cm)

Weight & Shipping Weight

Weight	3U, 5kW ~ 40 lbs (18kg) 3U, 10kW ~ 60 lbs (27kg) 3U, 15kW ~ 80 lbs (36kg) 6U, 20kW ~ 120 lbs (54kg) 6U, 25kW ~ 140 lbs (63kg) 6U, 30kW ~ 160 lbs (72kg)
Shipping Weight	3U, 5kW ~ 70 lbs (32kg) 3U, 10kW ~ 90 lbs (41kg) 3U, 15kW ~ 110 lbs (50kg) 6U, 20kW ~ 150 lbs (68kg) 6U, 25kW ~ 170 lbs (77kg) 6U, 30kW ~ 190 lbs (86kg)

New Expanded AC Product Line Featuring California Instruments

	Product Configurator

	DC Electronic Loads

	DC Modular Supply

	Discontinued Products

	Product Support

	Contact Sales

Programming & Read-back Specifications

	Programming		Read-Back / Monitoring
	Accuracy	Resolution	Accuracy	Resolution
Front panel Display	SGA: +/- (0.5%fs + 1 digit) SGI, Voltage: +/- 0.1% of full scale SGI, Current: +/- 0.4% of full scale	SGA: 3.5 digits SGI: 4.0 digits	SGA: +/- (0.5%fs + 1 digit) SGI, Voltage: +/- 0.1% of full scale SGI, Current: +/- 0.4% of full scale	SGA: 3.5 digits SGI: 4.0 digits	Knob control & Display read-back
Remote Analog Interface	Voltage: +/-0.25% of full scale for 0-5V range, +/-0.5% of full scale for 0-10V range Current: 0.8% of full scale	NA	+/-1.0% of full scale (0 - 10V)	NA	25-pin D-sub connector (0~5V or 0~10V)
Remote Digital Interface	Voltage: +/- 0.1% of full scale, Current: +/- 0.4% of full scale	+/-0.002% of full scale	Voltage: +/- 0.15% of full scale, Current: +/- 0.4% of full scale	+/-0.002% of full scale	RS-232C (Standard on SGI), Optional IEEE-488.2 and Optional LXI Compliant 10/100 base-T Ethernet (see Options)
OVP	+/- 1% of full scale	+/-0.002% of full scale			Programming range: 5-110% Configured from front panel, remote analog or via optional digital inputs
User I/O	Disconnect & Polarity-reversal relay control ( Only available with Ethernet Option )				Digital 10-pin Molex type connector Chart Below

Analog User I/O Pinouts

1	Isolated Remote ON/OFF	14	Isolated TTL/CMOS ON/OFF Control
2	Isolated Circuit Return	15	Remote Voltage Programming
3	Remote Overvoltage Set	16	Remote Current Programming
4	Voltage Return for Pins 9, 15, or 21	17	Fault State
5	Remote ON/OFF	18	Shutdown Fault
6	Circuit Common	19	Output Voltage Monitor
7	Output Current Monitor	20	Voltage Return for Pins 9, 15, or 21
8	Local Voltage Control Monitor	21	Voltage Control Resistance
9	Remote Voltage Programming	22	Current Control Resistance
10	Remote Current Programming	23	Current Return for Pins 10, 16, or 22
11	Local Current Control Monitor	24	Circuit Common
12	60V Remote Sense	25	Current Return for Pins 10, 16, or 22

Digital User I/O Pinouts ( Ethernet Option Only )

1	Fold Back Monitor
2	Direct Shutdown
3	Fault Indication
4	Trigger Out
5	Common
6	Polarity output reversal signal
7	Isolation relays relay open signal
8	Sense relays open signal
9	Common
10	Trigger in

Descripcion

Key Features

High Power Density: Up to 15 kW in a 3U / 30 kW in a 6U chassis
Wide Voltage Range: 0-40V up to 0-600V, in increments of 5 kW from 5 to 30 kW
Fast Load Transient Response: Protection from undesired voltage excursions
Low RMS and P-P Noise: Suitable for the most sensitive applications
Parallelable up to 150 kW: Expandable as your requirement grows
Modular Design: Upgradeable for the ultimate in investment protection
Sequencing: Program custom waveforms
Easy-to-read Fluorescent Display: SGI supports English, French, German, Italian, Spanish, Chinese, Japanese, and Korean languages
16-bit Resolution: Optional IEEE-488.2 + RS-232C + Ethernet provides precise control
Ethernet Control: LXI Class C compliant communication through integrated web server
Direct Relay Control: Control output and sense isolation relays, along with polarity relays. (Ethernet Option Only)
Hardware Trigger: Ethernet Option Only
5 Year Warranty

Comparte tu conocimiento de este producto con otros clientes... Se el primero en escribir un comentario

Navegue por mas productos en la misma categoria de este articulo:

Seleccion por Marca > Sorensen
Fuentes de poder > Fuente de Poder de DC
Fuentes de poder
Fuentes de poder > Fuentes de Poder de AC