![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Left_Top.gif) |
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Right_Top.gif) |
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
XBT 32-3FTP : Product Specifications
Output Ratings
Channel 1 and 2 Channel 3
Voltage (VDC) 0-32 0-15
Current (ADC) 0-3 0-5
Power (W) 96
30
Output Performance
Voltage Setting and Readback
Accuracy 0.01% + 5mV
Amplitude Resolution 1mV 1mV
Current Setting and Readback
Accuracy
0.1% + 3mA 0.1% + 3mA
Resolution
100 ìA 100 ìA
Voltage Ripple
0.5 mVRMS 1mVRMS
Voltage Noise
5 mVpp 20mVpp
Current Ripple
1mA 5mARMS
Load Regulation
Voltage 0.01% + 2mV 5mV
Current 0.01% + 300 ìA
Line Regulation
Voltage 0.01% + 2mV
Current 0.01% + 300 ìA
Stability (8 hours, constant load and temperature)
Voltage 0.02% + 2mV
Current 0.01% + 1mA
Temperature Coefficient (per C)
Voltage 0.01% + 3mV
Current 0.02% + 2mA
Transient Response 50ìS
Voltage Programming Time (typical)
Rise Time (Full Load) 1ms
3ms
Rise Time (No Load) 1ms
3ms
Fall Time (Full Load)
3ms 8ms
Fall Time (No Load)
250ms 250ms
Common
Memory Storage 100 setups
Timer 1 second to 100 hours
Regulatory Compliance cETLus (ANSI/UL61010-1-04, CAN/CSA C22.2 No. 61010-1-04) Compliant to CE Mark LVD EN61010-1, EMC EN61326
AC Input 115 / 230 VAC 10%, 47-63Hz
Operating Temperature 0 to 40 C
Storage Temperature -10 to +70 C
Weight 14.3 lbs. / 6.5 kgs
Size (WxHxD 8.5x5.3x17 in / 216x135x432 mm
Options and Accessories
M139 IEEE488.2 and Ethernet control interfaces
MHV Setup for 230V 10% AC Input
RM-XBT Rack mount kit for XBT Series power supplies
© 2009 AMETEK Programmable Power All rights reserved. AMETEK Programmable Power is the trademark of AMETEK Inc., registered in the U.S. and other countries.
Elgar, Sorensen, California Instruments, and Power Ten are trademarks of AMETEK Inc., registered in the U.S.
|
|
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Left_Bottom.gif) |
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Right_Bottom.gif) |
![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Left_Bottom.gif) |
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Right_Bottom.gif) |
![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Left_MidDiv.gif) |
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Right_MidDiv.gif) |
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
Descripcion
The Sorensen XBT32-3FTP adds to the capability of the Sorensen benchtop product line with a 16-bit triple output supply. Channels 1 and 2 can be programmed 0-32V and 0-3A each. The third output is fully programmable 0-15V, 0-5A up to a maximum of 30W. Channels 1 and 2 can be configured for tracking, parallel or series operation to, in effect, provide the equivalent of 6 different power supplies. In isolated mode, each of the 3 outputs functions independently; in tracking mode, channels 1 and 2 provide the same, but isolated output; in parallel mode, there is one 0-32V/0-6A output and one 0-15V/0-5A/30W output; in series mode, there is one 0-64V/0-3A output and one 0-15V/0-5A/30W output.
Safety of devices under test is paramount. The Sorensen XBT series of power supplies provides superior device protection. Each output is fully isolated with voltage/current preview before turning on the output. Built-in switches, in addition to enabling the preview mode, can configure the outputs for parallel or series connection while graphics on the front panel show the user where to make connections.
Advanced engineering features include storage of 100 different setups (voltage and current) as well as a 100 hour timer. Power- on state and synchronous or individual control of each channel output can also be set. Over-voltage and over-current protection is programmed for each channel.
Computer control is easily accomplished through industry-standard SCPI commands via the USB or RS-232C interfaces which come standard on every unit. The GPIB / Ethernet interface option allows 3 low power channels in a half-rack for ATE applications. This option also includes an 8-bit digital I/O which can be set as input or output signals for programming.
|
|
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Left_Bottom.gif) |
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
![](/v/vspfiles/templates/Template vdv/images/DBox_Border_Right_Bottom.gif) |
|
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif) |
![](/v/vspfiles/templates/Template vdv/images/clear1x1.gif)
|